Holiday Sale

This Friday and Saturday, I'll have a booth at the SEA Holiday Sale. If you're free, please join me to see my new work and a wide array of unique gifts. Please click here for a list of participating artists.

thanks, Peter

I love pie!

A couple years ago, our old rolling pin with the red handles started to fall apart. I made a rolling pin, similar to these, to replace it. These are native hard maple, displaying both heart and sapwood and have green milk paint in the small coves at each end. I turn each one to its diameter, sand and cut a small cove at each end, then turn off the lathe. I rotate the piece by hand to apply the milk paint to both coves. The pin comes off the lathe and I chop both ends to remove any trace of its having been attached to the lathe. Finally, the edges are sanded smooth, prior to 2 coats of walnut oil.

I call them green pins because of the green milk paint and because the maple is native and fairly local. The red handles of the old pin gave me the idea of adding some color to the ends.

This batch is curly, soft maple. They're all about 1 3/4" in diameter and about 18" long. With my palms on the pin to roll, I feel the dough respond to my movements. The length of the pin makes it easy for me to transfer the rolled dough to its pan.

I ask $32.00 per pin plus about $5.00 to $10.00 for shipping, depending on how far away you are. Please contact me here for more information. Green pins were just featured on a blog dedicated to exploring and highlighting flavor. Please go to www.flavorista.com for more. Pie is Good!

Work of the Hand, 20th year

Welcome to the Center for Maine Contemporary Art in Rockport, Maine. In early October, I'll be exhibiting in their 20th annual Work of the Hand, craft show. Please click here for more about the show. I'll be there Friday evening for the opening as well as volunteering Saturday morning. Approximately 50 fine crafts artists will be showing.

Furniture Masters' Auction

This Sunday, September 20th, is the annual Furniture Masters auction. This year it's in Manchester, NH, at The Currier Museum of Art. Our silent auction and reception go from 6 - 7:15 pm. The live auction starts at 7:30. This ash, hickory and Danish cord bench is my offering for this year's auction. To see all of this year's pieces, please click here.

On Friday, Saturday and Sunday the 20th, the Currier will be offering programs related to the Furniture Masters and the auction pieces. For more information on the tours, slide shows and demonstrations, please click here. This is an opportunity to see some wonderful furniture and the auction is great fun.

Ryan's Blanket Chest

I recently discovered that Bessey makes these angled clamping pads to fit their K-Body REVO clamps. They offer plenty of clamping power without a hint of slipping. They tilt from 0 to 15 degrees and saved me from having to make a set of angled cauls.

I had to make 2 small cauls to focus pressure at the ends of the lid divider.

With everything glued and cleaned-up, I can rout for the hinges and attach the lid. This shot shows the wedged through tenon for one foot. The frame and panel bottom goes in later.

I did a little splicing, attached the eye straps and now it's off to my friend Carl for stain and a lacquer finish.

The finish is 2 coats of stain and crystal lacquer. This color corresponds to the color of 2 lamps in the room that this chest will call home.

Laying-out angled through dovetails

This is the front of the lid of my blanket chest. Its ends are angled at 18 degrees. I remembered reading that angled dovetails need to be centered along a line that is parallel to a long edge. Laying-out off the angled end can lead to short grain problems at the tips of your tails. I start by striking a base line.

Using my small double square, I draw the centerlines of the sockets for the full pins.

I center the width of the base of the socket where my pencil line meets my base line.

For the top of the socket, I center its width where the pencil line meets the angled edge. I chose to make my sockets 3/8" at the bottom and 3/16" at the top. These measurements echo the pins in the chest.

I set my bevel gauge to connect the dots. You'll need a second gauge because the other side of the pin is at a different angle. With all the sockets marked on this side, you can square your lines across the end then angle them down the opposite face.

After sawing and paring, here's a finished end showing the 3 tails. If you cut a scrap to the same angle and lay-out typical dovetail as you would if the end were square, the difference will be clear.

Back at it

Here's the first of 2 photos of the bench that I built back in April. This one adorns my latest batch of postcards. This was shot by Dennis Griggs. Dennis shot all the photos in my portfolio.

This one was shot by Bill Truslow. Same piece but very different effect. This photo will be included in the catalog for this year's Furniture Masters auction. I love the way his lighting has worked its way through the woven seat and into the shadow.

This is a drawing of a blanket chest that I'm working on currently. Carol Bass designed it for clients of ours who have the live-edge trestle table in my portfolio. This was an early drawing and the feet ended up being from one piece. The box will be stained blue-green and the curly maple feet will remain their natural color.

Here's my progress, so far. In my next post I'll show how I laid-out the lid's angled dovetails.